supersonido
Grado Silver1 - 15253

Grado Silver1

189,00€
Stock disponible

Amplía tu garantía

Financiación 10 meses sin intereses, TAE 4,5%

+ info

Financiación ofrecida por Banco Cetelem S.A.U
El importe de la última cuota puede ser superior o inferior al resto debido al efecto del redondeo de los decimales.

Cápsula para giradiscos.

Características

Optimized Transmission Line (OTL) Cantilever/Stylus Assembly
Grado's OTL provides an ideal transfer of the signal from point to point, e.g., stylus to cantilever to magnet to coils, etc. This has been achieved by eliminating resonance at each of these key junctions. The transmission line cantilever consists of separate sections that are telescoped into each other. All sections are made of different alloys, some sections hollow, other sections solid. These sections are bonded together with materials that act as dampers, and are coated with a black proprietary material which controls and absorbs resonances that travel on the surface of the cantilever (known as skin effects). The OTL stylus/cantilever design will make your records sound quieter, improve the height, width, and depth of the soundstage, and offer more detail than previously obtainable. Cartridge Holography does exist...and that is what Grado's OTL technology is all about, more performance.

Pivoted-Fixed Axial Cantilever/Stylus Generator
This design feature is basically quite simple. The "OTL" cantilever shaft is brought to a fixed axial pivot that supports the entire cantilever assembly. A miniature element attached to the end of the cantilever is allowed to move freely within the lines of flux of a stationary magnet and coil structure. This system of support is mechanically more accurate (more linear) than conventional "teeter-totter" designs that utilize an iron armature to balance the mass of the cantilever. The teeter-totter design is supported in the center with a rubber donut mounting. The fixed axial design has a very low tip mass, which results in lower distortion, improved transient response, and longer record life.

Flux-Bridger Generator System
The Flux-Bridger design uses four separate magnetic gaps that the miniature element of the cantilever bridges. The miniature element moves between opposing flux gaps creating an increase in flux in one gap while reducing it in the other. The four separate magnetic gaps create a highly efficient and perfectly balanced system. This design requires fewer coil turns than conventional designs.

Optimized Transmission Line (OTL) Cantilever/Stylus Assembly
Grado's OTL provides an ideal transfer of the signal from point to point, e.g., stylus to cantilever to magnet to coils, etc. This has been achieved by eliminating resonance at each of these key junctions. The transmission line cantilever consists of separate sections that are telescoped into each other. All sections are made of different alloys, some sections hollow, other sections solid. These sections are bonded together with materials that act as dampers, and are coated with a black proprietary material which controls and absorbs resonances that travel on the surface of the cantilever (known as skin effects). The OTL stylus/cantilever design will make your records sound quieter, improve the height, width, and depth of the soundstage, and offer more detail than previously obtainable. Cartridge Holography does exist...and that is what Grado's OTL technology is all about, more performance.

Pivoted-Fixed Axial Cantilever/Stylus Generator
This design feature is basically quite simple. The "OTL" cantilever shaft is brought to a fixed axial pivot that supports the entire cantilever assembly. A miniature element attached to the end of the cantilever is allowed to move freely within the lines of flux of a stationary magnet and coil structure. This system of support is mechanically more accurate (more linear) than conventional "teeter-totter" designs that utilize an iron armature to balance the mass of the cantilever. The teeter-totter design is supported in the center with a rubber donut mounting. The fixed axial design has a very low tip mass, which results in lower distortion, improved transient response, and longer record life.

Flux-Bridger Generator System
The Flux-Bridger design uses four separate magnetic gaps that the miniature element of the cantilever bridges. The miniature element moves between opposing flux gaps creating an increase in flux in one gap while reducing it in the other. The four separate magnetic gaps create a highly efficient and perfectly balanced system. This design requires fewer coil turns than conventional designs.

Cápsula GRADO SILVER1:

    Respuesta de Frecuencia: 10-60
    Tipo de cápsula: Imán móvil
    Separación de canales 1KHz: 35 db
    Impedancia de entrada: 47K
    Salida a 1KHz 5CM/sec: 5mV
    Peso recomendado: 1.5gr
    Tipo de aguja: eliptica.
    Inductancia: 45mH
    Resistencia 475
    Compliance: 20
    Peso: 5,5 gr

Utilizamos cookies propias y de terceros para mejorar nuestros servicios y mostrarle publicidad relacionada con sus preferencias mediante el análisis de sus hábitos de navegación. Si continua navegando, consideramos que acepta su uso.

cerrar